Features

Design benefits

waterproof

Moderate rain for 2 hrs 5,000 mm Schmerber (JIS standard) Pockets not waterproof

breathability

Very breathable coated fabric (RET < 12): reduces condensation

pockets

3 secure pockets, including 1 inner pocket

windproof

Fabric especially coated to reduce the cooling effect of the wind.

Design details

Waterproofing 1/2

We measure the fabric resistance to water pressure in mm of water column (based on the JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is. On our Sailing 100 jacket: Component is resistant to water pressure of 5,000 mm Schmerber (JIS standard). This equates to the average pressure applied by the water during a rain shower. The anorak's waterproofness was tested in a rain shower with 60 litres of water / m² / hour for 2 hours.

Waterproofing 2/2

- High collar - Injection-moulded plastic to avoid salt oxidation - Water-repellent components (water runs off the fabric) - 100% taped seams - Central opening features a flap with a drainage channel for optimal waterproofing

Hood

The hood does not pack down into the collar, it is attached. Completely depth and height-adjustable hood. Visor with a headband to provide a good level of protection and a better hold. The high neck effectively protects the neck.

Pockets

2 zip pockets on the front of the jacket to put your hands or some items 1 inside pocket on the right side of the chest with a rip-tab closing NOTE: the pockets are NOT WATERPROOF

Front zip closure

A zip on the entire jacket length with an interior flap protects against the wind and water. Soft fabric flap on the top of the collar to protect the chin.

Fabric breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability. We consider that if: RET < 9 = highly breathable fabric 9 < RET < 12 = breathable fabric The RET of the Sailing jacket 100 is 12.

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in. Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered. The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended. Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full-rinse cycle or extra rinse.

How to reactivate the anorak's water repellency

Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator. Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

frequency	occasional
weather conditions	rainy weather
rain	moderate rain
neck type	zip neck
type of opening/closing	zip
number of pockets	3 pockets
customisation	not customizable
reversible	not reversible
zip type	full zip
type of lining	light/no lining
snow skirt	without snow skirt
waterproof	waterproof, water repellent
hood	with hood
pocket	zip closed pocket, with pocket, closed pocket
breathability	breathable
fit	standard
style	plain
membrane construction	2 layers
ventilation system	without ventilation
mm H2O (Schmerbers)	5,000 mm
main material	polyamide
type of length	at the hips
condition	new
windproof	windproof
lining material	synthetic
reinforced area	without reinforced area
sleeves length	long sleeves
modular	not modular
stitching type	with seam
reflective	without reflective zones
type of waterproofing	coating
thumb pass	without thumb pass
type of hood	adjustable hood, hood with visor
breathability (in RET)	RET 6 < RET < 12 : moderately breathable
top length	standard
storage	without storage

Raw material	89.014%
Manufacturing	2.495%
Packaging	0.627%
Distribution	4.158%
Use	3.172%
End of life	0.534%

Waterproof sailing jacket - wet-weather windproof jacket SAILING 100 navy blue

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Cleaning

Environmental impact

Carbon footprint

Ecodesign approach